ASTM A663 PDF

This standard is issued under the fixed designation A /A M; the number 2 For referenced ASTM standards, visit the ASTM website, , or. See the chemical composition and physical properties of ASTM A Grade 75 [ ], find alternative materials, and connect with suppliers. ASTM-A Standard Specification for Steel Bars, Carbon_材料科学_工程科技_ 专业资料。ASTM A,商品级,碳素钢棒,机械性能规范.

Author: Tauzshura Goltigul
Country: Thailand
Language: English (Spanish)
Genre: Art
Published (Last): 25 April 2018
Pages: 43
PDF File Size: 16.59 Mb
ePub File Size: 3.97 Mb
ISBN: 639-4-46021-142-3
Downloads: 14358
Price: Free* [*Free Regsitration Required]
Uploader: Arashikus

The specimens shall undergo a tension test to determine tensile strength, yield point and elongation. This standard is subject to revision at any time by the responsible satm committee and must be reviewed every? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. No further reproductions authorized.

Current edition approved May 1, Internal porosity, surface seams, and other surface irregularities may be present in this quality. The bars shall be available in round, square and hexagonal shapes.

ASTM A663 Grade 75 [515]

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. The minimum ksi Zstm requirement does not change. This aztm standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade TBT Committee.

  LORETTA ORTIZ AHLF DERECHO INTERNACIONAL PUBLICO PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Link to Active This link will always route to the current Active version of the standard.

This standard has been approved for use by agencies of the Department of Defense. This specification covers hot-wrought merchant quality carbon steel bars and bar size shapes produced to mechanical property requirements and intended for noncritical constructional applications.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The tension specimen may be aged as described in Test Methods and De? ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The merchant quality bars shall be from visible pipe; however, they may contain pronounced chemical segregation. Test specimens for material over 11? For material over 2 in.

NOTE 1—Special quality hot-wrought carbon steel bars subject to mechanical property requirements are covered in Speci? A number in parentheses indicates the year of last reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Combining values from the two systems may result in non-conformance with the standard. Individual reprints single or multiple copies of this standard may be obtained ast contacting ASTM at the above address or at phonefaxor service astm.

  GLSEN SAFE SPACE KIT PDF

Permission rights to photocopy the standard may also be secured from the ASTM website www.

ASTM-A Standard Specification for Steel Bars, Carbon_百度文库

The bars shall also be furnished as rolled and not pickled, blast cleaned, or oiled. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at a6663 address shown below.

Originally approved in However, for material 2 in.

Historical Version s – view previous versions of standard. Approved May 1, Machined sides of bend test specimens may have the corners rounded to satm radius of not over 1?

Combining values from the two systems may result in non-conformance with the standard. Internal porosity, surface seams, and other surface irregularities may be present in this quality.

The test report, if required, shall show yield strength. This abstract is a brief asm of the referenced standard.

If test specimens are selected conforming to the dimensions of Fig. The values stated in each system may not be exact equivalents; therefore, each 1 This speci?

The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace sstm.