Search among more than user manuals and view them online Find great deals for Aton DLA4 Four Room Speaker Switch With Volume Control. Shop with confidence on eBay!. Free Shipping on many items across the worlds largest range of Aton Dla4 In Home Audio Equalizers. Find the perfect Christmas gift ideas with eBay.

Author: Aragal Necage
Country: Kenya
Language: English (Spanish)
Genre: History
Published (Last): 2 February 2006
Pages: 323
PDF File Size: 20.35 Mb
ePub File Size: 6.56 Mb
ISBN: 138-6-91729-541-4
Downloads: 96325
Price: Free* [*Free Regsitration Required]
Uploader: Voodoogrel

You will lose any product warranty on the unit. Speakers rated between 4 Ohms sla4 8 Ohms can be matched with ampliers also rated from 4 to 8 Ohms. Add an optional RF remote and receiver in order to have full control anywhere in the house.

ATON Stereo Receiver DLA4 User Guide |

Set the volume in each room to the desired level. If it ickers, IR ooding is indicated.

The IR indicator will be solid red when the room is wton, solid off when the room is on, or solid purple when the room is on and unselected. Programming additional remotes can be accomplished in a matter of seconds. Carefully peel the appropriate Room Identication Label from the card and place it in the Room Label Location for the chosen room.

Remote Control batteries are dead Replace batteries 1. See above Perform steps above 2.

For more information and purchase options, visit our website at: Turn power for the output device OFF before making connections. Without releasing the Room button, press and hold the Vol – Button. Set the Zone 2 volume level to the point where it achieves the maximum listenable level prior to lda4.


Aton DLA4 Four Room Speaker Switch With Volume Control

Once the Scene Preset has been saved, the Room LEDs for the rooms included in the Scene Preset will blink on and off four times and the system will return to the levels prior to setting cla4 Scene Preset.

When using this setting, maximum volume is reduced to 10 steps. Connect the equipment into an outlet on a circuit different from that to which da4 receiver is connected. If the volume level prior to turning the room off is lower or equal to the Maximum Turn-On Volume Level, the room will come back on at the last volume.

Protect the power supply cord from being walked on or pinched, particularly at plugs, outlets and the point where they exit from the apparatus.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. Make sure to match the impedance of the speakers and ampliers as noted. Speakers in room miswired or atom a. Provisions exist for IR, Ground, and Voltage.

Good exercise, too – especially when your system is located downstairs or on the other side of the house. Verify connections No audio present in any room Hum or buzz through system speakers Poor audio quality 26 1. Most speakers are 4 or 8 Ohms. Check IR indicator on front panel.

ATON DLA4 manuals

Like the previous example, a pair of speakers are connected to the DLA2s Room 1 Speaker Outputs, while an additional pair of speakers is connected to the Room 2 Speaker Outputs.

Push it again – they go off. Figure and Table ato description and location of Rear Panel connections. Press the Room Button for the desired room. Increase the separation between the equipment and receiver.


Ground loop Ensure proper grounding using a three prong grounded AC outlet.

This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat. Place the receiver in a convenient location; preferably as high as possible.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

Please report the problem to your dealer immediately. Test known good speaker at back panel speaker connector b. It’s a community-based project which helps to repair anything. Use Rack screws not included to attach the assembled unit to the equipment rack as shown in Figure D If the volume level prior to turning the room off is higher than the Maximum Turn-On Volume Level, the room will come back on at the Maximum Turn-On Volume Level instead of the last volume.

Press Play, turn ON, etc. Verify that the impedance levels of the amp and speaker are not lower than 8 Ohms. If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly contacts ATON at or service atonhome.